ANALISIS PENGARUH VARIASI DIAMETER PIPA DAN POSISI TAKE-IN PROBE TERHADAP KARAKTERISTIK ALIRAN FLUIDA PADA SISTEM PERPIPAAN AUTOMATIC SAMPLER CRUDE OIL MENGGUNAKAN METODE CFD

  • Hermawan Saputra Universitas Negeri Padang
  • Delima Yanti Sari Universitas Negeri Padang
  • Randi Purnama Putra Universitas Negeri Padang
  • Fitrah Qalbina Universitas Negeri Padang
Keywords: Automatic Sampler, Computational Fluid Dynamics (CFD), Pipe Diameter, Pressure Drop, Wall Shear Stress, Crude Oil, Take-In Probe, Piping System

Abstract

This study aims to analyze the effect of pipe diameter variation and take-in probe position on fluid flow characteristics in a crude oil automatic sampler piping system using the Computational Fluid Dynamics (CFD) method. The automatic sampler system plays a critical role in obtaining representative crude oil samples; however, high-viscosity fluids often cause flow instability due to improper piping design and mismatch between pump specifications and operating conditions. This research investigates pipe diameter variations of 1 inch, 2 inches, and 3 inches, as well as pipe inclination angles of 45° and 90°. Numerical simulations were conducted using ANSYS Fluent 2025 R1 with three-dimensional modeling and boundary conditions based on actual field operating data. The analyzed parameters include velocity distribution, pressure drop, head loss, wall shear stress, and Reynolds number. The simulation results indicate that smaller pipe diameters generate higher pressure drop and wall shear stress due to increased flow velocity, while larger diameters result in lower energy losses but may create low-velocity regions that reduce flow homogeneity. Pipes with a 90° inclination exhibit greater energy loss compared to those with a 45° inclination. All flow variations remain within the laminar flow regime due to the high viscosity of the crude oil. Overall, a medium-to-large pipe diameter combined with a 45° inclination is considered the most optimal configuration for maintaining flow stability and improving crude oil sampling quality.

References

Afolabi, R. O., Yusuf, E. O., Okonji, C. V., & Nwobodo, S. C. (2019). Predictive analytics for the Vipulanandan rheological model and its correlative effect for nanoparticle modification of drilling mud. Journal of Petroleum Science and Engineering, 183(July). https://doi.org/10.1016/j.petrol.2019.106377
Andreasen, A., Borroni, F., Nieto, M. Z., Stegelmann, C., & Nielsen, R. P. (2018). On the adequacy of API 521 relief-valve sizing method for gas-filled pressure vessels exposed to fire. Safety, 4(1). https://doi.org/10.3390/safety4010011 API 598.pdf. (n.d.).
Api, A. M., Bartlett, A., Belsito, D., Botelho, D., Bruze, M., Bryant-Friedrich, A., Burton, G. A., Cancellieri, M. A., Chon, H., Cronin, M., Crotty, S., Dagli, M. L., Dekant, W., Deodhar, C., Farrell, K., Fryer, A. D., Jones, L., Joshi, K., Lapczynski, A., … Thakkar, Y. (2024). RIFM fragrance ingredient safety assessment, 2,6-xylenol, CAS Registry Number 576-26-1. Food and Chemical Toxicology, 194(S1), 115118.https://doi.org/10.1016/j.fct.2024.115118
API Gravity. (2016). Pollution Control Handbook for Oil and Gas Engineering, 1, 141–142. https://doi.org/10.1002/9781119117896.ch7
Berti, S., Fracassi, P., Mattioli, A., Potula, V. R., & Lotti, C. (2014). Design and development of a specially modified positive displacement rotary screw pump and relevant hydraulic circuit to enhance “entrained air handling” capability in a closed loop lube oil system. Journal of Engineering for Gas Turbines and Power, 136(7), 1–12. https://doi.org/10.1115/1.4026543
Cană, P., Ripeanu, R. G., Diniță, A., Tănase, M., Portoacă, A. I., & Pătîrnac, I. (2025). A Review of Safety Valves: Standards, Design, and Technological Advances in Industry. Processes, 13(1), 1–42. https://doi.org/10.3390/pr13010105
Drews, A. (2008). Standard Practice for Automatic Sampling of Petroleum and Petroleum Products. Manual on Hydrocarbon Analysis, 6th Edition, 5854, 646-646–24. https://doi.org/10.1520/mnl10929m
Emerson. (2008). Oil & Gas Custody Transfer - Crude oil. 1–4.
Graham, E., Yang, M., Barton, N., Harvey, R., Paton, R., Mills, C., Learmonth, D., Mark Jiskoot, & Gordon, A. (2012). Issues and challenges with pipeline sampling. 30th International North Sea Flow Measurement Workshop, NSFMW 2012, October, 1–29.
Hagen, I., & Brewer, D. (1983). Seed Production Research Usda-Ars Cooperating.
Seed Production Research at Oregon State University USDA-ARS Cooperating, Ext/CrS 50, 9.
High, U., Performance, A., Heavy, S., & Sampler, D. (n.d.). Auto Sampling. Indra, Z. (2019). APLIKASI FLOW SWITCH PADA RANCANG BANGUN SIRKULASI AIR RUMAH TINGGAL Abstrak Prosiding Seminar Nasional Teknik Elektro Volume 4 Tahun 2019. 4, 2–6.
ISO INTERNATIONAL STANDARD 3171 Second edition 1988-12-01. (1988). 1988.
Jalal, N. I., Ibrahim, R. I., & Oudah, M. K. (2022). Experimental investigation and optimization process for viscosity reduction in crude oil pipelines using dilution and electrical field. AIP Conference Proceedings, 2415(January), 66–75. https://doi.org/10.1063/5.0093833
Kasim, M., & Arife, W. (2021). Performance analysis of cavitation flow pump. IOP Conference Series: Materials Science and Engineering, 1090(1), 012044. https://doi.org/10.1088/1757-899x/1090/1/012044
Maulana, A., Sarungu, S., & Syamtinningrum, M. D. P. (2024). Analisis Penerapan Sistem Otomasi dengan Menggunakan Automatic Inline Sampler dalam Pengambilan Sampel pada PT. XYZ. Indonesian Research Journal on Education, 4(1), 358–365. https://doi.org/10.31004/irje.v4i1.1198
Meškuotienė, A., Kaškonas, P., Urbonavičius, B. G., Dobilienė, J., & Raudienė, E. (2025). Ensuring Measurement Integrity in Petroleum Logistics: Applying Standardized Methods, Protocols, and Corrections. Applied Sciences (Switzerland), 15(12), 1–22. https://doi.org/10.3390/app15126886
Mpms, U. A. P. I. (2017). Best Practices for Custody Transfer Using API MPMS 18.2.
Muñoz, J. A. D., Ancheyta, J., & Castañeda, L. C. (2016). Required Viscosity Values to Ensure Proper Transportation of Crude oil by Pipeline. Energy and Fuels, 30(11), 8850–8854. https://doi.org/10.1021/acs.energyfuels.6b01908
Oliveira, G. P., Santos, M. D., & Roque, W. L. (2020). Constrained clustering approaches to identify hydraulic flow units in petroleum reservoirs. Journal of Petroleum Science and Engineering, 186(December 2019), 106732. https://doi.org/10.1016/j.petrol.2019.106732
Pedersen, K. S., Fredenslund, A., Christensen, P. L., & Thomassen, P. (1984).
Viscosity of crude oils. Chemical Engineering Science, 39(6), 1011–1016. https://doi.org/10.1016/0009-2509(84)87009-8
Saadat, M., Vikse, N. B., Øye, G., & Dudek, M. (2021). A microfluidic study of oil displacement in porous media at elevated temperature and pressure.
Scientific Reports, 11(1), 1–12. https://doi.org/10.1038/s41598-021-99796-7
Supendi, A., & Fitri, M. (2022). Pemilihan Spesifikasi Komponen Alat Uji Prestasi Pompa Menggunakan Metode Analisis Persamaan Bernoulli Jurnal
Teknik Mesin : Vol . 11 , No . 1 , Februari 2022 ISSN 2549-2888. Jurnal Teknik Mesin, 11(1).
Teknis, K., & Pompa, P. (2025). FEED PUMP REPLACEMENT BATANG PSO
Issued for Review.
Tim Independen Pengendalian Keselamatan Migas. (2020). Zero Unplanned Shutdown Zero Fatality. Atlas Keselamatan Migas, 3, 55–60.
Wang, J. (2011). Theory of flow distribution in manifolds. Chemical Engineering Journal, 168(3), 1331–1345. https://doi.org/10.1016/j.cej.2011.02.050
Wilson, T. P., Miller, C. V., & Lechner, E. A. (2024). Guidelines for the use of
automatic samplers in collecting surface-water quality and sediment data.
U.S. Geological Survey Techniques and Methods, 2024. https://doi.org/10.3133/tm1D12
Wong, B., & McCann, J. A. (2021). Failure detection methods for pipeline networks: From acoustic sensing to cyber-physical systems†. Sensors,
21(15). https://doi.org/10.3390/s21154959
Published
2026-01-24
How to Cite
Hermawan Saputra, Delima Yanti Sari, Randi Purnama Putra, & Fitrah Qalbina. (2026). ANALISIS PENGARUH VARIASI DIAMETER PIPA DAN POSISI TAKE-IN PROBE TERHADAP KARAKTERISTIK ALIRAN FLUIDA PADA SISTEM PERPIPAAN AUTOMATIC SAMPLER CRUDE OIL MENGGUNAKAN METODE CFD. EDU RESEARCH, 6(4), 3229-3241. https://doi.org/10.47827/jer.v6i4.1969
Section
Articles