PENGARUH FRAKSI VOLUME SERAT TERHADAP KEKUATAN TARIK DAN MEKANISME PATAHAN PADA MATERIAL KOMPOSIT BERPENGUAT SERAT DAUN PANDAN DURI (PANDANUS TECTORIUS)
Abstract
This study aims to evaluate the effect of volume fraction variations of screw pine fiber (Pandanus tectorius) on the tensile strength and fracture mechanism of epoxy resin matrix composite materials. An experimental method was employed with fiber volume fractions of 5%, 7.5%, and 10%. Specimen fabrication was carried out via the hand lay-up technique, while tensile testing was executed according to the ASTM D638 standard. Each volume fraction consisted of five specimens, yielding a total of 15 tested samples. The fracture mechanism was examined microscopically to identify failure characteristics across each volume fraction. The results indicated that variations in fiber volume fraction significantly affect the tensile strength of the composite. A 5% volume fraction achieved an average tensile strength of 24.551 MPa, which dropped to 22.132 MPa at 7.5%, and subsequently rose to 25.348 MPa at 10%. The 10% volume fraction also recorded an elastic modulus of 25.850 GPa with an elongation of 1.303%. Microscopic observations revealed that the 5% and 7.5% volume fractions were predominantly characterized by fiber pull-out and debonding. In contrast, the 10% volume fraction exhibited more frequent fiber breakage, indicating enhanced capacity of the fibers to transfer and sustain loads. In conclusion, fiber volume fraction variations influence the tensile strength and fracture mechanism of screw pine fiber-reinforced epoxy composites, with the highest tensile strength achieved at a 10% fiber volume fraction (25.348 MPa).
References
Aminur, dkk. 2024. “Analisa Kekuatan Tarik dan Lentur Komposit Berpenguat Serat Daun Nanas (Ananas comosus) dengan Konfigurasi Cross-Ply Laminate”. Jurnal Teknologi Terapan, Volume 10, Nomor 2 (hlm. 70–79).
Bisono, R. M., dkk. 2023. “Analysis of Tensile and Bending Properties of Epoxy Resin Matrix Composites Using Variations of Pandanus tectorius Leaf Fibers”. International Journal of Science, Engineering, and Information Technology, Volume 8, Nomor 1 (hlm. 433–436).
Bledzki, A. K. dan J. Gassan. 1999. “Composites Reinforced with Cellulose Based Fibres”. Progress in Polymer Science, Volume 24, Nomor 2 (hlm. 221–274).
Callister, W. D. Jr. dan D. G. Rethwisch. 2018. Materials Science and Engineering: An Introduction. Edisi Ke-10. Hoboken: John Wiley & Sons.
Elfaleh, I., dkk. 2023. “A Comprehensive Review of Natural Fibers and Their Composites: An Eco-Friendly Alternative to Conventional Materials”. Results in Engineering, Volume 19, 101271.
Faruk, O., dkk. 2012. “Biocomposites Reinforced with Natural Fibers: 2000–2010”. Progress in Polymer Science, Volume 37, Nomor 11 (hlm. 1552–1596).
Friedrich, K., dkk. 2005. Polymer Composites: From Nano- to Macro-Scale. New York: Springer.
Gibson, R. F. 2016. Principles of Composite Material Mechanics. Edisi Ke-4. Boca Raton: CRC Press.
Hartini, D., dkk. 2022. “Tensile Strength Analysis of Sea Pandan Leaves (Pandanus tectorius) Fiber Reinforced Epoxy Composite”. Vortex, Volume 3, Nomor 2 (hlm. 108–115).
Hartini, D., dkk. 2024. “The Mechanical Properties of the Sea Pandan Leaves (Pandanus tectorius) Fiber-Reinforced Epoxy Composite Were Assessed Using Bending Tests”. Dalam Proceedings of the 5th Annual Advanced Technology, Applied Science, and Engineering Conference (ATASEC 2023) (hlm. 185–194). Atlantis Press.
Hidayat, R. dan A. Catur. 2022. “Pengaruh Fraksi Volume Serat Pandan Laut terhadap Kekuatan Bending dan Tarik Komposit Polyester”. Effect of Volume Fraction Pandanus tectorius Fibers Against Bending and Tensile Strength of Polyester Composites.
Hull, D. dan T. W. Clyne. 1996. An Introduction to Composite Materials. Edisi Ke-2. Cambridge: Cambridge University Press.
Imon, I. H. 2024. “Sustainable Natural Fiber Based Composites Materials: A Review”. Tersedia pada https://doi.org/10.26434/chemrxiv-2024-4tcbv.
John, M. J. dan S. Thomas. 2008. “Biofibres and Biocomposites”. Carbohydrate Polymers, Volume 71, Nomor 3 (hlm. 343–364).
Mahmud, M. Z. A., dkk. 2025. “Synthesis and Applications of Natural Fiber-Reinforced Epoxy Composites: A Comprehensive Review”. SPE Polymers, Volume 6, Nomor 1.
Mark, J. E. (Ed). 2007. Physical Properties of Polymers Handbook. Edisi Ke-2. New York: Springer.
Marpaung, R. A. K. 2018. “Hubungan Kekerabatan 8 Spesies Marga Pandanus Berdasarkan Karakter Morfologi dan Anatomi”. Jurnal Education and Development, Volume 6, Nomor 1.
Mohanty, A. K., dkk. 2000. “Biofibres, Biodegradable Polymers and Biocomposites: An Overview”. Macromolecular Materials and Engineering, Volume 276–277, Nomor 1 (hlm. 1–24).
Mohanty, A. K., dkk. 2001. “Surface Modifications of Natural Fibers and Performance of the Resulting Biocomposites: An Overview”. Composite Interfaces, Volume 8, Nomor 5 (hlm. 313–343).
Mohanty, A. K., dkk. (Eds). 2005. Natural Fibers, Biopolymers, and Biocomposites. Boca Raton: CRC Press.
Muhajir, M. 2016. Analisis Kekuatan Tarik Bahan Komposit Matriks Resin Berpenguat Serat Alam dengan Berbagai Varian Tata Letak. Skripsi. Malang: Universitas Negeri Malang.
Mukhtar, D. 2016. “Analisa Kekuatan Tarik Komposit dengan Penguat Serat Pelepah Kelapa Sawit”. Jurnal Teknik Mesin, Volume 3, Nomor 2 (hlm. 7–12).
Mutmainnah, A. F., dkk. 2025. “Sea Pandan Leaf Fiber as an Alternative Material for Upper Limb Orthosis”. JPOST Journal of Prosthetics Orthotics and Science Technology, Volume 4, Nomor 1 (hlm. 37–43).
Pickering, K. L., dkk. 2016. “A Review of Recent Developments in Natural Fibre Composites and Their Mechanical Performance”. Composites Part A: Applied Science and Manufacturing, Volume 83 (hlm. 98–112).
Purnomo, M. J., dkk. 2025. “Study on Mechanical Properties of Pandan Duri (Pandanus tectorius) Fiber-Reinforced Biocomposites Materials for Aerospace Application”. Dalam Proceedings of the Adisutjipto Aerospace, Science and Engineering International Conference (AASEIC 2024) (hlm. 95–101). Atlantis Press.
Ramful, R. 2024. “Mechanical Performance and Durability Attributes of Biodegradable Natural Fibre-Reinforced Composites—A Review”. Journal of Materials Science: Materials in Engineering, Volume 19.
Rong, M. Z., dkk. 2001. “The Effect of Fiber Treatment on the Mechanical Properties of Unidirectional Sisal-Reinforced Epoxy Composites”. Composites Science and Technology, Volume 61, Nomor 10 (hlm. 1437–1447).
Satyanarayana, K. G., dkk. 2009. “Biodegradable Composites Based on Lignocellulosic Fibers—An Overview”. Progress in Polymer Science, Volume 34, Nomor 9 (hlm. 982–1021).
Sgriccia, N., dkk. 2008. “Characterization of Natural Fiber Surfaces and Natural Fiber Composites”. Composites Part A: Applied Science and Manufacturing, Volume 39, Nomor 10 (hlm. 1632–1637).
Stone, B. C. 1982. “Pandanus tectorius Parkins. in Australia: A Conservative View”. Botanical Journal of the Linnean Society, Volume 85, Nomor 2 (hlm. 133–146).
Sulaiman, M. dan M. H. Rahmat. 2018. “Kajian Potensi Pengembangan Material Komposit Polimer dengan Serat Alam untuk Produk Otomotif”. Dalam Seminar Nasional Teknik Mesin Universitas Jember (SISTEM) 2018.
Syafri, E., dkk. 2022. “Isolation and Characterization of New Cellulosic Microfibers from Pandan Duri (Pandanus tectorius) for Sustainable Environment”. Journal of Natural Fibers, Volume 19.
Yan, L., dkk. 2014. “Flax Fibre and Its Composites A Review”. Composites Part B: Engineering, Volume 56 (hlm. 296–317).

